It’s Absolutely Critical that When the Power Fails the Generator Works
During a power outage, it’s vital that your customer’s emergency power system works every time! Remotely monitoring a standby generator helps to make sure that the emergency power system is ready for the next power failure. If a problem occurs, you’ll be alerted about it immediately so you can provide a fast, proactive service response.
Our PT Series of monitoring products are the perfect choice for almost all standby generator applications. Our products are simple to install, very affordable, universal for all generators, and utilizes the Power Link platform. PLUS ALL PT Series monitoring products come with our lifetime warranty.
All PT Series solutions monitor and log the following standard conditions:
- Generator On (Running) and Generator Off (Stopped)
- Engine Battery Voltage with Low Battery Alarm
- Exercise Tracker with Missed Exercise Alert
- Run Time Tracker with Excessive Run Time Alerts
The PT Series monitors have anywhere from 4-7 additional inputs to customize any installation. These inputs can be configured to monitor any condition including some of the common conditions below:
- Common Fault
- Common Warning/Pre-Alarms
- Low Fuel Level
- Generator Switch Not in Auto
- Low Coolant Temperature
- Low Coolant Level
- High Engine Temperature
- Low Oil Pressure
- Over Speed
- Over Crank
- Fuel Leak Detected
- All inputs can be custom configured
Additional accessory kits are available to monitor other conditions including:
- Utility Power On/Off
- On Generator Power
- Return to Utility Power
- Generator Breaker Open
Products
The PT150 generator monitoring system is the ideal basic solution for residential air-cooled standby generators and some small liquid-cooled generators. This monitor includes an integral 36″ harness, has two (2) additional digital inputs and can monitor the primary operational conditions of the generator.
Includes First 12 Months of Monitoring Service Plan
Description:
- PT150 Monitor – Fully Configured & Scripted
- Internal Cellular & GPS Antenna
- Wiring Harness Internal to Unit
- 2 Digital Inputs
- 1 Relay Driver Output
- 7-32VDC Power
- Cellular Carrier Activation
- Over-The-Air Unit Configuration and Updates
Manual
The PT300 generator monitoring system is a full featured solution for any residential, commercial or industrial outdoor standby generator. This monitor includes a custom harness, has four (4) additional programmable bias inputs and one (1) ADC input. The PT300 digital inputs are used with generator controller outputs and accessory kits. When configured with the appropriate accessory kits, the PT300 can log the full sequence of operation of the emergency power system.
Includes First 12 Months of Monitoring Service Plan
Description:
- PT300 Monitor – Fully Configured & Scripted
- Internal Cellular & GPS Antenna
- Custom Connection Harness
- 4 Digital Inputs
- 1 ADC Input
- 3 Relay Driver Outputs
- 12-24VDC Power
- Internal 1000mAh Lithium Ion Battery
- Cellular Carrier Activation with Verizon or AT&T
Manual
The PT300E generator monitoring system is a full featured solution for any residential, commercial or industrial indoor or outdoor standby generator. This monitor includes a custom harness, has four (4) additional programmable bias inputs and one (1) ADC input. The PT300E digital inputs are used with generator controller outputs and accessory kits. When configured with the appropriate accessory kits, the PT300E can log the full sequence of operation of the emergency power system.
Includes First 12 Months of Monitoring Service Plan
Description:
- PT300E Monitor – Fully Configured & Scripted
- External Cellular & GPS Combo Antenna
- Custom Connection Harness
- 4 Digital Inputs
- 1 ADC Input
- 3 Relay Driver Outputs
- 12-24VDC Power
- Internal 1000mAh Lithium Ion Battery
- Cellular Carrier Activation with Verizon or AT&T
Manual
The PT400 generator monitoring system is a comprehensive solution for monitoring all of the major alarm points for any indoor or outdoor standby generator application. This monitor includes a power harness, custom I/O harness, has seven (7) additional programmable bias inputs and three (3) ADC inputs. The PT400 digital inputs are used with generator controller outputs and accessory kits. When configured with the appropriate accessory kits, the PT400 can log the full sequence of operation of the emergency power system.
Includes First 12 Months of Monitoring Service Plan
Description:
- PT400 Monitor – Fully Configured & Scripted
- External Cellular & GPS Antenna – Magnetic Mount
- Power Harness and Custom I/O Connection Harness
- 7 Digital Inputs
- 4 ADC Inputs
- 5 Relay Driver Outputs
- 12-24VDC Power
- Internal 1000mAh Lithium Ion Battery
- Cellular Carrier Activation with Verizon or AT&T
Manual
The PT500 generator monitoring system is a comprehensive solution for monitoring all the major alarm points for any indoor or outdoor standby generator application. The PT500 is includes three different connection modes including Ethernet, WiFi and Cellular. This monitor includes a power harness, custom I/O harness, has seven (7) additional programmable bias inputs and three (3) ADC inputs. The PT500 digital inputs are used with generator controller outputs and accessory kits. When configured with the appropriate accessory kits, the PT500 can log the full sequence of operation of the emergency power system.
Includes First 12 Months of Monitoring Service Plan
Description:
- PT500 Monitor – Fully Configured & Scripted
- 4G LTE Cellular Connectivity
- Two (2) RJ45 Ethernet Ports
- Optional WiFi Antenna and Dedicated Access Point
- External Cellular & GPS Antenna
- Power Harness and Custom I/O Connection Harness
- Internal 1Ah Lithium Ion Backup Battery
- 7 Digital Inputs
- 3 ADC Inputs
- 5 Relay Driver Outputs
- 7-32VDC Power
- Cellular Carrier Activation
- Over-The-Air Unit Configuration and Updates
- Generator On (Running)/Off (Stopped)
- Engine Battery Voltage Monitor with Low Battery Alarm
- Generator Failed to Exercise (Missed Exercise Cycle)
- Extended Run Time Alerts – Generator Running for 4, 8, 12 & 24 Hours
- Remote Start Relay Driver Output (Customer Furnished Relay)
Manual
Power Telematics can provide custom application solutions. Contact our sales team at 678-992-5501 to discuss your application to help find the best solution for your requirements.